Getting a Car Part from any US Online Store

As you all know, Scratchy has a JDM OBD1 SOHC VTEC D16A engine. All local Civics of its generation run on OBD1 non-VTEC engines. So finding a brand new distributor (an ignition part, not the one who sells to stores/dealers) for my engine is a PITA (Surplus parts are available. However, these run for P4-5K -- overpriced for a used part).

Tried scouring Banawe, but they only have the one for the ESI or PH12 which are incompatible with VTEC SOHC. Replacement brands run for P6 to P8K and it's kinda expensive if you ask me. 

Then, I stumbled upon this site on a local car forum: http://gmettrading.com/.

They can buy from any website in the States, ship it here (with a cost of course), and all you need to do is to pick it up from their office. I guess this is my chance to buy the cheap TD-42U distributor from Amazon that I've been eyeing on for quite some time now. 

I emailed them and I received friendly replies even though I have a lot of questions. They gave me a quote for the item for P5,450. Knowing that this is in fact lower than the brand new replacements here, I went for it. I deposited half the amount into their BDO account and that's it, they ordered it for me. All I have to do is wait and pay the balance upon pick-up.

ETA is around August 8 or 9, 2013. I'll let you know once it arrives. :)

The Not-so-major Underchassis Refresh

I came to realize after years of using Scratchy, that its front underchassis parts were long due for replacement. It was still rolling on its OEM parts for 21 years already. Leaking rear shoks, cracked trailing arm bushings, clunking sound up front, and bump steer were some of the indications I needed to refresh the underparts.

First thing to do was to find what needs to be replaced first. I went to a couple of shops: Motech Cainta, Goodyear Servitec Marcos Highway, BlackSheep Autoworks, and Yokohama Gil Fernando.

Motech quote on parts and labor (in parenthesis):
Upper Arm Assembly Pair - P3,600 (P560)
Rack End Pair - P2,200 - (P560 including tie rod)
Tie Rod Pair - P1,900
Lower Ball Joints Pair - P2,200 (P560)
CVJ Boot - P200 (P240)
Alignment - P560
Motech TOTAL: P12,580

And knowing I could buy original 555 replacement parts cheaper from Banawe, my succeeding inquiries were just for labor.

Goodyear quoted me on labor for a few parts and were even more expensive than Motech. Knowing this, I got the quote and never intended to return.

Yokohama, on the other hand, said that I only need to replace the left upper arm and one rack end together with the CVJ boot. What I liked about them was that they didn't recommend replacing parts that were not yet due for replacement.  And labor was quite reasonable, too. So no breaking the bank for me.

I also got a quotation from BlackSheep for labor:
Rear Shocks Pair - P500
Trailing Arm Bushings - P1,600
Tie rod pair, rack end pair, lower ball joints pair - P1,000
Upper Suspension Pair - P350
Left CVJ Boot - P300
BlackSheep TOTAL Labor: P3,750

That said, I bought all the parts I need from LVC in Banawe:

Rear Shocks Pair KYB - P3,400.00
Trailing Arm Bushings - P900.00
Tie Rod End Pair 555 - P1,000.00
Rack End Pair 555 - P1,160.00
Lower Ball Joint Pair 555 - P1,100.00
Upper Suspension Assembly Pair - P2,000.00
Constant Velocity Joint Boot (L) - P215.00
CVJ Grease - P65
LVC Parts TOTAL - P8,940

I started having the shocks installed in BlackSheep, done in 30 minutes! Paid P500 for it. Then after a week, I returned to Motech. I know that BlackSheep was cheaper by a few hundered pesos, but I was willing to pay more in Motech for their relatively trained mechanics.

Here are the parts:

And the car while being worked on:

Some additional parts that were needed to be bought while installing:

1. Additional grease for the inner CVJ - P65
2. A new boot, since the one given to me by LVC was for an EK! Damn LVC! - P150

GRAND TOTAL for parts: P9,155

I think I had a break on labor. I had all the things to be done quoted again and they just asked for P1,000 for tie rod, rack end, ball joints, and boot. And since removing the knuckle would mean leaving only 2 bolts for upper arm to be replaced, I asked the mechanic to do that for me. I also added front alignment for P280.

So that's P1,000 + P500 (for shocks) + P280 (for alignment) + P300 (for the upper arm and mechanic tip)

GRAND TOTAL for labor: P2,080

Next in line would be the trailing arm bushings and if budget permits, Energy Suspension set for EG!

Will update you guys when that happens.

GE Jazz Rims Pretty Thick Tires: What to Do?

Recently had a deal with one of my old mates in a car club.

Got these for a reasonable price:

I've decided to sell the wheels to anyone who needs it. How much do 2011 OEM Jazz 15-inch wheels sell for anyway? However, I still don't know what to do with the tires.

Tires included are GT Champiro 55 at 195/55/15. A piece costs around P3,000 in tire shops around the metro. Two of which are at around 70% tread, and the other pair are at around 90%. 

Option 1: Replace my Falken ZE 502 set with these on my Spoons? I just don't know if it would look good on it.

Option 2: Install these on my 15s steelies? Steelies are just 5.5" wide.

Option 3: Sell the tire set? What's a fair price?

What do you think? Hit the comments to help me decide. :)

The Secondary Clutch Impromptu Repair

For a long time now, I was intending to replace my secondary clutch because it was still the original piece since 1992.

True enough, this plan slipped my mind, and darn... got me while cruising along Amang Rodriguez Avenue early this morning.

Clutch hits the floor and never returns. The entire reservoir of clutch fluid was on the asphalt.

I caused a bit of traffic build up, so I've no choice but to have Scratchy towed. Towing is free BTW thanks to Wheelers Club International (be a member now for only P700!).

Back home:

The culprit: a 21-year-old secondary clutch cylinder. A photo of its location, above where the leaks are.

Here it is in disassembled form together with a repair kit I bought from a nearby auto supply (the kit comes with the piston and rubber boot):

While at it, painted using Bosny Hi Temp flat black:

Fully assembled like new!

 Installed back into the car.

A summary of what happened.

I suggest you do this as a preventive maintenance to your ageing EGs. Total cost for repair is only P150 which almost cost me thousands more if not for the Wheelers membership.

Soft-spoken Scratchy Now Screeming with a Spoon N1 Muffler

The legendary Spoon N1 Muffler. A dream part for the inner child in every Honda lover.

I got one at a somewhat cheap price: P9,500 for a slightly modified original 1st Generation Spoon N1.
This particular one is for a sedan, but the owner modified (shortened) the pipe to fit the hatch.

The Gen 1 Spoon N1 Muffler features a matte/flat steel finished body and polished tip -- different from the succeeding generations that have a Spoon badge and 100% polished body.

Here it is when I bought it:

And moments before installing, a closer look. Notice the clean welds? That's what sets it apart from copies/fakes.

Installation time!

Remove the rear bumper so you can easily see what you're doing.

This is an OEM JDM EG6 B16A muffler and pipe set BTW.

OEM vs. Spoon N1

Take off two bolts that connect the muff to the midpipe, then install the Spoon muff. Pretty straightforward if you ask me.

Done!

Looking at the pics, you would say that it is a perfect fit. However, due to the fact that this just a modified part, a portion of the pipe is hitting my LCA whenever I hit bumps on the road so further modification is needed.

Now on to Brodeth. A trusted muffler and pipe fabricator of many car enthusiasts.

The muffler and car while waiting for them to start work:

This is the fit I'm looking at:

I decided to replace the pipe altogether. It hurts to see them cut the pipe, but it's all for the better.

Ouch!

All its glory exposed.

TIG welding it and the finished product.

Now, fitting it into the car:

Finished work!

I don't care whether it lost its value by doing this since I don't plan to sell the muffler anytime soon.

I paid Brodeth a total of P2,500 for everything.

What do you guys think?

Update: Bought a Spoon N1 Gen3. Click here.